Archives of Loren Williams Fly Tying Tutorials.
Poly Wing Rusty Spinner

Fly and Photos by Loren Williams

Mayfly imagoes, or "spinners," are an incredibly important food source for the fly angler. These fully mature mayflies have just completed the mating and egg-laying rituals and are succumbing to death. With wings outstretched, the bugs lay helpless and motionless on the surface, going only where the currents take them. Very often this "spinner fall" happens at dusk, or very early in the morning. For these reasons, trout are all over them! Logically it makes sense: the bugs are easily captured and can be found virtually anywhere there is current-often collecting in mass along seams, foam lines, and in back eddies. Using the low light conditions as cover, trout can ease into shallow water or hang just under the surface and sip these morsels at will, expending very little energy. This is an equation that can equal some very big trout!

Fishing spinners poses a few difficulties for many anglers. The first problem is realizing when the trout are eating spinners and not duns or some other insect. Anglers need to be alert to what is going on over their heads. Spinners will come out of the vegetation, often at treetop level, where they will gather in a cloud to mate. After mating, the males will depart and die and the females will lay their eggs and die. Usually the progress of the event can be tracked as the cloud gets lower and lower to the water. Once the bugs are at eye level you can expect the trout to turn on to them.

The other issue at hand is imitating theses creatures. Spinners will develop transparent wings, long tails and slim, often darker bodies, when they molt from the dun or sub imago stage. These features will be represented differently on the water's surface especially in the calmer areas that the trout tend to await them. In order to be consistently successful you'll need patterns which are flush floating, durable and provide an accurate footprint on the surface.

Poly-wing spinners are often my first choice, and rarely let me down. Durability is insane, important when you are fishing at the brink of darkness. The features are accurate and the overall fly is slim. Deadly!

This Rusty Spinner will adequately match most mayfly spinners since they just about all molt into an adult with a rich brown body. Notable exceptions are green drakesand the various sulphurs species.

MATERIALS

Hook: Partridge SLD (#10-#18)
Thread:
Brown
Wings:
Light Dun Poly yarn or similar buoyant synthetic yarn
Tails:
Microfibetts
Body:
Cinnamon Brown Dubbing

Click photo to enlarge!

Poly Wing Rusty Spinner

Place barbless hook firmly in your vise.

Poly Wing Rusty Spinner

Making a long tag end, s tart the jam knot behind the hook eye and run it all the way rearward on the shank, binding the tag to the top of the shank.

Poly Wing Rusty Spinner

Place the thread tag in your material clip and run the thread forward to the 1/4 point of the shank.

Poly Wing Rusty Spinner

Select your favorite synthetic buoyant yarn in a light dun or white color.

Poly Wing Rusty Spinner

Select a bundle twice as thick as you wish one wing to be. I make my wings on the sparse side.

Poly Wing Rusty Spinner

With the tips forward, measure the material to be equal to the overall hook length.

Poly Wing Rusty Spinner

Slide the measured point forward to the thread.

Poly Wing Rusty Spinner

Secure to the top of the shank with several tight wraps.

Poly Wing Rusty Spinner

Bind rearward to about the middle of the shank.

Poly Wing Rusty Spinner

Clip the excess close and come forward with the thread to the 1/4 point of the shank.

Poly Wing Rusty Spinner

Pull the material firmly up and back.

Poly Wing Rusty Spinner

Form a small thread dam to support the wings temporarily upright, but more importantly perpendicular to the hook.

Poly Wing Rusty Spinner

Divide the wing into two equal section with your fingers.

Poly Wing Rusty Spinner

Grasp the near wing by its tips and pull it down to the same plane as the hook shank and angled slightly to the rear.

Poly Wing Rusty Spinner

Come, front to back, with several thread wraps between the wings.

Poly Wing Rusty Spinner

Grasp the far wing and pull it down to the plane of the hook and slightly to the rear.

Poly Wing Rusty Spinner

This time come rear to front with the thread as you lay several wraps to divide the wings in the spent position.

Poly Wing Rusty Spinner

Nicely spent wings. Notice how sparse.

Poly Wing Rusty Spinner

Taper the butt ends of the wing material as you take the thread to the rear. Stop as the rear edge of the thorax area.

Poly Wing Rusty Spinner

Obtain some light colored Microfibett tailing material.

Poly Wing Rusty Spinner

Remove 4 individual "barbs," keeping the tapered tips even.

Poly Wing Rusty Spinner

With the tips to the rear, measure to be equal to 1.5 times the hook length.

Poly Wing Rusty Spinner

Keeping the measured point at the rear edge of the hook...

Poly Wing Rusty Spinner

...secure the tailing material to the shank at the rear of the thorax.

Poly Wing Rusty Spinner

Secure them to the top of the shank as you wrap to the bend. You can best do this by holding the fibers up at a slight angle as you wrap back on them.

Poly Wing Rusty Spinner

Come back to the thorax with the thread.

Poly Wing Rusty Spinner

Pull the thread tag up between the tail fibers, splitting them 2 per side. As long as you kept the tag and the fibers on top of the shank you will end up with nicely split tails. The harder you pull the tag forward, the wider they will splay. I like them at about 45-degrees. When you find the position you like, secure the tag with several thread wraps. Clip the thread tag and excess tail fibers.

Poly Wing Rusty Spinner

Take the thread to the rear stopping short of the tail.

Poly Wing Rusty Spinner

Dub your thread with a VERY thin tight dubbing. No need to dub right up to the hook. This is why we do not run the thread back to the rear. You can use up the gap of naked thread as you take the thread back to the tail, this ensures your first wrap of dubbing goes on right at the end of the abdomen.

Poly Wing Rusty Spinner

Dub a thin, tight body right up tight to the rear of the wings. Be careful not to trap wing fibers.

Poly Wing Rusty Spinner

Make a series of X-Wraps between the wings to dub that section of the thorax. Keep it thin. Usually one series is sufficient.

Poly Wing Rusty Spinner

Pull the wings out of the way.

Poly Wing Rusty Spinner

Dub the forward section of the thorax, stopping short of the hook eye.

Poly Wing Rusty Spinner

Build a neat head. Whip and clip. Cement for durability.

Poly Wing Rusty Spinner

A completed Poly-Wing Rusty Spinner!